ICALEO 2009 Paper #202 (Laser Surface Treatment of Engineering Ceramics and the Effects Thereof on Fracture Toughness)
Laser Surface Treatment of Engineering Ceramics and the Effects Thereof on Fracture Toughness
Authors:
Pratik Shukla, Loughborogh University; Leicestershire Great Britain
J. Lawrence, -; -
Presented at ICALEO 2009
Surface treatment of Si3N4 and ZrO2 engineering ceramics with a CO2 laser and a fibre laser was conducted to identify changes in the fracture toughness (K1c). Vickers macro hardness indentation tests were employed prior to and after the laser treatment to investigate the near surface changes in the hardness of the engineering ceramics. Optical microscopy was then used to observe the near surface integrity, crack lengths and crack geometry within the engineering ceramics....$28.00
ICALEO 2009 Paper #201 (Investigation into Time Dependant Degradation and Atmospheric Conditions on the Wettability of Nylon 6,6 which Has Undergone CO2 Laser Surface Modification)
Investigation into Time Dependant Degradation and Atmospheric Conditions on the Wettability of Nylon 6,6 which Has Undergone CO2 Laser Surface Modification
Authors:
David Waugh, Loughborough University; Loughborough Great Britain
Jonathan Lawrence, Loughborough University; Loughborough Great Britain
D.J. Morgan, -; -
Presented at ICALEO 2009
Although CO2 lasers have been shown to be capable of modifying the wettability of polymeric materials, it is known that the CO2 laser induced wettability modifications of these materials can degrade over time. This can be seen to be crucial from a commercial point of view as this would indicate that a shelf-life has to be establis...$28.00
ICALEO 2009 Paper #1910 (FOCAL SHIFT MONITORING AND COGNITIVE CLOSED-LOOP CONTROL BY ANALYSIS OF CO-AXIAL VIDEO DATA)
FOCAL SHIFT MONITORING AND COGNITIVE CLOSED-LOOP CONTROL BY ANALYSIS OF CO-AXIAL VIDEO DATA
Authors:
Thibault Bautze, LDV, Technical Univ. of Munich; Munich Germany
Tobias Kaiser, FSR, Technical Univ. of Darmstadt; - Germany
Sonja Huber, IWB, Technical Univ. of Munich; Munich Germany
Presented at ICALEO 2009
Most laser welding heads offer the ability to connect a co-axial camera, using the same focusing lenses as the laser beam. Thus, the focal shift induced by heating the lenses and thus influencing the laser beam, alters the video data acquired. In the proposed approach, the sharpness of the video data is used to monitor the focal shift and distance changes relative ...$28.00
ICALEO 2009 Paper #1908 (Comparison of Powder Additive Qualities with Regard to Achievable LMD Results)
Comparison of Powder Additive Qualities with Regard to Achievable LMD Results
Authors:
Marco Goebel, Llt, Chair for Laser Technology Rwth Aachen; Aachen Germany
Steffanie Linnenbrink, Llt, Chair for Laser Technology Rwth Aachen; Aachen Germany
Ingomar Kelbassa, Llt, Chair for Laser Technology Rwth Aachen; Aachen Germany
N. Ludwig, -; -
Presented at ICALEO 2009
Laser Metal Deposition (LMD) is a common technology used for local repairs and additive manufacturing of complete parts 3D applications such as aero engine and automotive components as well as for wear and corrosion protection of parts 2D cladding applications such as tools, dies, a...$28.00
ICALEO 2009 Paper #1907 (Application of Holographic Beam Shaping in Selective Laser Melting for the Fabrication of Functional Polymer Components)
Application of Holographic Beam Shaping in Selective Laser Melting for the Fabrication of Functional Polymer Components
Authors:
Darrel Bunyan, Loughborough University; Loughborough Great Britain
Richard Heath, Loughborough University; Loughborough Great Britain
John Tyrer, Loughborough University; Loughbrough Great Britain
Matthew Gibson, Loughborough University; Loughborough Great Britain
Presented at ICALEO 2009
The applications of selectively laser sintered polymer components have been greatly limited by their poor mechanical properties as a result of high levels of residual porosity. This paper looks at the effects of using holographic beam shaping to...$28.00
ICALEO 2009 Paper #1904 (Effect of Path Planning on Residual Stress Distribution in Laser Powder Deposition Process)
Effect of Path Planning on Residual Stress Distribution in Laser Powder Deposition Process
Authors:
Ehsan Foroozmehr, Southern Methodist University; Dallas TX USA
Radovan Kovacevic, Rcam-Smu; Dallas TX USA
Presented at ICALEO 2009
One of the important parameters in laser powder deposition process is the deposition path pattern that affects final quality of the deposited material. In this study, a finite element method is used to model the thermal and structural behavior of the laser powder deposition process. An area is defined to be covered with AISI H13 powder with three different deposition patterns: one-section, two-section, and three-section. The two-section pattern divides th...$28.00
ICALEO 2009 Paper #1903 (Effect of Substrate on Temperature Field in Selective Laser Sintering of Metal Powders)
Effect of Substrate on Temperature Field in Selective Laser Sintering of Metal Powders
Authors:
Xianfeng Shen, Institute of Machinery Manufacturing Technology; Mianyang Peoples Republic of China
Yang Wang, -; -
Jialin Yang, -; -
Presented at ICALEO 2009
Selective laser sintering (SLS) of metal powders is an attractive Rapid Prototyping and Manufacturing (RPM) technology which can be used to produce three-dimensional metal parts directly from a CAD model. In the process, the substrates are commonly used for avoiding the balling effect in powder melting and dislocation of sintered part. A three-dimensional finite element thermal model in SLS of metal powder including t...$28.00
ICALEO 2009 Paper #1902 (Effects of Parameters on Surface Roughness of Samples by Selective Laser Melting)
Effects of Parameters on Surface Roughness of Samples by Selective Laser Melting
Authors:
Zemin Wang, Huazhong University of Science and Technology; Wuhan Peoples Republic of China
Guangxia Chen, Jianghan University; Wuhan, Hubei Province Peoples Republic of China
Kai Guan, Huazhong University of Science and Technology; Wuhan, Hubei Province Peoples Republic of China
Changwen Peng, Huazhong University of Science and Technology; Wuhan, Hubei Province Peoples Republic of China
Xiaoyan Zeng, Huazhong University of Science and Technology; Wuhan, Hubei Province Peoples Republic of China
Presented at ICALEO 2009
During fabrications of metal parts by...$28.00
ICALEO 2009 Paper #1809 (Microlens Fabrication with Fiber Laser Induced Thermo-Mechanical Plastic Forming Method)
Microlens Fabrication with Fiber Laser Induced Thermo-Mechanical Plastic Forming Method
Authors:
Tao Chen, Institute of Laser EngineeringBeijing University of Technology; Beijing Peoples Republic of China
Tong Wang, Institute of Laser Engineering, Beijing University of Technology; Beijing Peoples Republic of China
Ji-Min Chen, Institute of Laser EngineeringBeijing University of Technology; Beijing Peoples Republic of China
Tie-Chuan Zuo, Institute of Laser EngineeringBeijing University of Technology; Beijing Peoples Republic of China
Shi-Bing Liu, Institute of Laser Engineering,Beijing University of Technology; Beijing Peoples Republic of China$28.00
ICALEO 2009 Paper #1808 (Analysis and Control of Penetration Depth Fluctuations in Single-mode Fiber Laser Welds)
Analysis and Control of Penetration Depth Fluctuations in Single-mode Fiber Laser Welds
Authors:
Yong Chae Lim, The Ohio State University; Columbus OH USA
Matt Reiter, Ohio State University; Columbus OH USA
Jungho Cho, Ohio State University; Columbus OH USA
Dave Farson, The Ohio State University; Columbus OH USA
M. Mehl, Honeywell FM&T; - USA
Presented at ICALEO 2009
Penetration depth fluctuations of single-mode fiber laser welds made with long focal length optics and the affects of sinusoidal laser power modulations were studied. It was found that the welds had a high aspect ratio and were subject to spiking defects. The magnitude of the pene...$28.00
Pages
There is currently no content classified with this term.